[Xastir] Xastir setup
Tom Russo
russo at bogodyn.org
Sun Nov 15 13:06:12 PST 2020
On Sun, Nov 15, 2020 at 09:00:45PM +0000, we recorded a bogon-computron collision of the <kb8uih88 at charter.net> flavor, containing:
> Tom, Thanks for responding. I checked your instructions and checked my
> settings. All seem to be as you suggest, with a few tweaks. I
> discovered a major bleep up in my radio to tnc cable as the mic audio
> was not wired correctly to the tnc.
Yes, that would do it.
> Now that is corrected, I am tx
> packet data, digi'd by a local igate and so things seem to be going
> correctly. I will watch it now and see how things go.
> Thank you again!!
Glad you're up and running. Enjoy.
> -----------------------------------------From: "Tom Russo"
> To: "Xastir - APRS client software discussion"
> Cc:
> Sent: Sunday November 15 2020 3:37:01PM
> Subject: Re: [Xastir] Xastir setup
>
> Set up your station configuration with coordinates in
> File->Configure->Station
>
> Set up beacon type in File->configure->Defaults
>
> Set up beacon frequency in File->Configure->Timing
>
> Look in your interface settings in Interface->Interface Control and
> make sure
> that you have set up your TNC correctly as an interface and that
> "Allow Transmitting" is turned on.
>
> If it is all right, then open View->Incoming Data to watch what your
> interfaces
> see, and then click "Interface->Transmit Now". You should see your
> packet
> show up in the Incoming Data window. If you do not, your interface
> may not
> be set up correctly. If you do see it, watch your radio to see if it
> is
> actually transmitting (that is, do it again while watching your
> radio).
>
> If your radio is transmitting but nobody is seeing your packets, your
> TNC
> audio may not be set correctly and may be creating packet audio that
> is not
> decodable. See page 18 of the TNC Pi manual for how to adjust
> transmit
> audio on the device.
>
> On Sun, Nov 15, 2020 at 08:22:35PM +0000, we recorded a
> bogon-computron collision of the flavor, containing:
> > I am unclear about setting up station data and beaconing. I am a
> fixed
> > station, entered mu coordinates but am not sending any routine
> packets
> > with any data. Not showing up on aprs.fi. An Igate digi is in
> within
> > range of me. I see his packets and am receiving packets from about
> 100
> > miles away so far. When I tested with a local ham to see if he saw
> my
> > packets he did not see any thing. I saw his packets(BPQ).
> > I am using rasp pi model 3 and a tnc pi from coastal chip works.
> > Thanks in advance for any help
> > ChrisKB8UIH
> > _______________________________________________
> > Xastir mailing list
> > Xastir at lists.xastir.org
> > [1]
>
> Links:
> ------
> [1] http://xastir.org/mailman/listinfo/xastir
> http://xastir.org/mailman/listinfo/xastir
> />
> --
> Tom Russo KM5VY
> Tijeras, NM
>
> echo
>
> _______________________________________________
> Xastir mailing list
> Xastir at lists.xastir.org
> http://xastir.org/mailman/listinfo/xastir
--
Tom Russo KM5VY
Tijeras, NM
echo "prpv_a'rfg_cnf_har_cvcr" | sed -e 's/_/ /g' | tr [a-m][n-z] [n-z][a-m]
More information about the Xastir
mailing list